Go Back   Jeep Garage - Jeep Forum > Jeep Platform Discussion > 2011+ Dodge Durango-WD

Join Jeep Garage Today
Reply
 
Thread Tools Display Modes
 
  #1  
Old 06-26-2012, 11:54 AM
Scottina06's Avatar
JeepGarage Founder
My Jeep: 2014 6.4L SRT8 WK2
 
Join Date: May 2009
Location: Berea, Kentucky
Posts: 48,983
Thanks: 855
Thanked 877 Times in 647 Posts
Rep Power: 7717588
Scottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond repute
Garage
**HOW-TO** add oem HID's to your Durango WD or Grand Cherokee WK2

The way I did it was to buy the oem repair harness for the drivers side(silly...but there isnt one for the pass side) I have all the pin outs etc below. Basically though....I just needed that repair harness from justforjeeps.com and the canbus fix harnesses

Now for the passenger side I had to improvise since theres no repair harness to use...therefore no oem connector for the OEM headlight. I went simple...I bought a phillips d1s ballast that included the power/ground wiring and the bulb wire. I think it was from some sort of cadillac. Then I wired a plug into the power and ground for the canbus fix to plug into. Then I just cut a whole in the rubber bulb cover and siliconed it up for the bulb wire to run through. Plug the can bus fix harnesses directly into the h11 low beam bulb connector....all the other bulbs are plug and play!

Heres the part #'s needed

**drivers repair harness and plug-68052582AA
*drivers side plug layout


**canbus fix harness at xenondepot-
http://www.kbcarstuff.com/CANBUS-Fix-p/cbfix.htm
heres the harness finished-

For the passenger side-theres no repair harness from Mopar...so i bought a single d1s ballast with the bulb wire and power wire as shown below and wired in the following componets-
**You will also need 2 h11 plug to wire into d1s ballast shown below

**here is the ballast I bought from the caddy. I simply connected the power and ground from this ballast to the power and ground for an h11 female headlight plug. I then cut a slit in the rubber bulb cover and fed the silver plug from this ballast through the hole to the bulb. I then used the canbus fix between the power/ground h11 plug and the oem h11 plug from the truck.


The results-

__________________

__________________
SCOTT
The HARDER you work...the LUCKIER you are!
2014 REDLINE red Jeep SRT "BLOODIED Edition" 1 of 1
Previous JEEP rides-
2013 Jeep Grand Cherokee SRT-deep cherry
2013 JKU 10th anniversary-white
2006 Jeep Grand Cherokee Laredo-inferno red



Twitter-The_Jeep_Guy
Instagram-thejeep_guy

Reply With Quote
  #2  
Old 06-26-2012, 08:55 PM
CMil527's Avatar
Member
 
Join Date: Mar 2012
Location: Old Bridge, NJ
Posts: 264
Thanks: 0
Thanked 3 Times in 3 Posts
Rep Power: 1140
CMil527 is on a distinguished road
Re: **HOW-TO** add oem HID's to your Durango WD or Grand Cherokee WK2

Great info as always!
__________________

__________________
Reply With Quote
  #3  
Old 10-30-2012, 09:33 AM
Jeep_addicted's Avatar
Premium Member
My Jeep: 2012 3.6L WK2
 
Join Date: Nov 2011
Location: St. Thomas US. Virgin islands
Posts: 1,066
Thanks: 15
Thanked 42 Times in 36 Posts
Rep Power: 1331984
Jeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond reputeJeep_addicted has a reputation beyond repute
Garage
Re: **HOW-TO** add oem HID's to your Durango WD or Grand Cherokee WK2

12 Pin plug to make OEM bi Xenon Retrofit more PLUG & Play
__________________
  • '12 Laredo X V6 Deep Cherry Dark/Mid Greystone, QT1
  • Outside: colormatched Altitude Grille, S Limited rear valance, Euro frt. bumper moulding, Rear chrome trim. Sharkfin, 20% tint, RFUK (built my own)
  • Inside: Alcantara steering wheel/shift knob,SRT dash trim, illuminated front scuff plates, stainless rear scuff plates, bright pedals, F/R footwell lights
  • Performance: OEM dual exhaust conversion, HD brakes, E-code projectors, JW Speaker fogs
Reply With Quote
  #4  
Old 02-04-2013, 08:21 PM
New Member
My Jeep: 2011 5.7L
 
Join Date: Feb 2013
Location: fayetteville, nc
Posts: 2
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 0
primosx95 is on a distinguished road
Re: **HOW-TO** add oem HID's to your Durango WD or Grand Cherokee WK2

About to do this MOD just got the parts in, I have the canbus fix, the repair harness and the 12 pin plug. For the passenger side do I replace the current plug with the 12 pin plug and do I still need to use the canbus fix for this side
__________________
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
adding OEM HID's to 2011+ Grand Cherokee/Durango Scottina06 Interior/Exterior/Visual 35 09-13-2012 06:13 PM
2011 Grand Cherokee Laredo... HID's? AIR_RAM XenonDepot 8 01-12-2012 08:42 PM

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 06:06 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community