Drag link? 05 hemi - Jeep Garage - Jeep Forum

Go Back   Jeep Garage - Jeep Forum > Jeep Platform Discussion > Grand Cherokee - WK > Troubleshooting/Problems

Join Jeep Garage Today
Reply
 
Thread Tools Display Modes
 
  #1  
Old 02-18-2015, 08:35 PM
Member
 
Join Date: Dec 2014
Posts: 45
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 769
jdmm08 is on a distinguished road
Drag link? 05 hemi

Where is the drag link on 05 hemi 4x4 WK? I have code C2205- steering angle sensor. I replaced the clock spring and it's still there. Though I noticed my steering wheel is 1/4 turn off and I can't find the drag link on this thing or find any mention of it online. Getting frustrated with how unfriendly and cramped this hemi is........ Tks for any replies.


Sent from my iPad using JeepGarage

Reply With Quote
Sponsored Links
Advertisement
 
  #2  
Old 02-20-2015, 10:41 AM
Member
My Jeep: 2005 5.7L WK
 
Join Date: Jul 2010
Location: Kingston, Ontario
Posts: 953
Thanks: 2
Thanked 40 Times in 39 Posts
Rep Power: 277861
dr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond repute
Re: Drag link? 05 hemi

No drag link on a rack and pinion setup (like the WKs).

It sounds like something wasn't aligned when you replaced the clockspring.
Reply With Quote
  #3  
Old 02-20-2015, 01:50 PM
Member
 
Join Date: Dec 2014
Posts: 45
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 769
jdmm08 is on a distinguished road
Re: Drag link? 05 hemi

Ok I'll research the rack and pinion set up.


Sent from my iPhone using JeepGarage
Reply With Quote
  #4  
Old 02-21-2015, 06:04 PM
Member
 
Join Date: Dec 2014
Posts: 45
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 769
jdmm08 is on a distinguished road
Re: Drag link? 05 hemi

It's now giving a U 110a code that looks the scm. I also pulled the driver side wheel cover and don't see any logical way to make any adjustments.

As for the clock spring replacement there was only one way to put the wheel back on as it has a notch on the steering column.

Any experience on this?


Sent from my iPhone using JeepGarage
Reply With Quote
  #5  
Old 02-25-2015, 02:12 PM
Member
My Jeep: 2005 5.7L WK
 
Join Date: Jul 2010
Location: Kingston, Ontario
Posts: 953
Thanks: 2
Thanked 40 Times in 39 Posts
Rep Power: 277861
dr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond reputedr.lee.baugh has a reputation beyond repute
Re: Drag link? 05 hemi

Never had the steering wheel off, so can't say for sure.

I think that the only "adjustment" that will be possible will be at the inner tie rods. You can take it in for an alignment and have them set it straight. If it is outside of the correction possible via a good alignment, I would bet it's the wheel or something is bent.
Reply With Quote
  #6  
Old 02-25-2015, 05:19 PM
Member
 
Join Date: Dec 2014
Posts: 45
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 769
jdmm08 is on a distinguished road
Re: Drag link? 05 hemi

Just did that yesterday. It was out of alignment and that fixed the steering wheel issue.

The codes, service elec brake, and traction control are still there now with a flashing tpms. I'm going to replace the pressure sensors when they come in and go from there....


Sent from my iPhone using JeepGarage
Reply With Quote
  #7  
Old 03-01-2015, 05:55 PM
Member
 
Join Date: Dec 2014
Posts: 45
Thanks: 0
Thanked 1 Time in 1 Post
Rep Power: 769
jdmm08 is on a distinguished road
Re: Drag link? 05 hemi

I think I found it. I can get a star scan tool and follow these instructions but problem is I have no idea how to adjust the I-shaft. "Case Number K56486465

Vehicle Issue ABS lamp on. Fault codes C1219 and U0126 logged in the ABS module.;The SCCM must never be replaced unless it has an internal fault related specifically to the SCCM module. If the following conditions are found: - fault codes C1219 and U0126 are logged in the ABS module - the SCCM has no internal faults (active or stored) - the ESP and ABS icons are on and - the Service Electric Brake System message appears The fix is relatively simple and does not require replacing an SCCM.

System or Component Will Not Clear,Will Not Reset,Will Not Turn Off;DTC / Error Message;ABS System,ABS Light / Anti-Lock Light;Yes - Continuously

Recommendation 1) Connect the Starscan tool to the diagnostic connector, power up the tool and set the ignition key to run. 2) Confirm C1219 and U0126 is stored or active in the ABS module. 3) Confirm no faults are active or stored in the SCCM. 4) Position the steering wheel so the tires are pointing straight ahead. 5) Use tool and go to the LID in the ABS or SCCM to observe SAS position. If greater than 360 degrees, you must re-center the SCCM/SAS. Fastest way to re-center the SCCM/SAS is: A) Remove knee blocker to access the steering column/intermediate shaft (I-shaft) knuckle bolt. B) Remove the bolt and slide the I-Shaft off the column shaft. C) While monitoring the SAS position with the tool, rotate the steering wheel at least 360 degrees so the angular position decreases towards 0 degrees (zero). Remember, if the tires are pointing straight ahead, we should be at 0 +/- 30 degrees, so we can reattach the I-shaft and tighten the bolt. D) Clear the faults in the ABS and turn the ignition switch off and then on twice to ensure the cluster warnings and respective faults do not reappear. If the fault reappears, refer to intermittent diagnostics. Please note that Service part numbers have been released to allow for the replacement of necessary components versus replacing the entire SCCM assembly. Service P/N's Hazard SW 05143309A$ Wiper/ Wash 05143310A$ Turn Signal Base 05143311A$ Turn W F Fog 05143312A$ Turn W F Fog and Auto 05143313A$ Turn W R Fog 05143314A$ Turn W R Fog and Auto 05143315A$ Cancel Cam 05143321A$~ Electronic Box (inc CSR) w/o SAS 05143319A$ Electronic Box (inc CSR) w/ SAS 05143320A$
Modification Date
01/02/06 4:32 PM
Reply With Quote
Reply

Tags
hemi

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Hello...any drag racers here? WJracer New Members - Welcome! 28 02-18-2010 08:46 PM

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 05:05 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2016, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community

JeepGarage.org is in no way associated with or endorsed by FCA US LLC. Chrysler, Dodge, Jeep, Ram, Mopar and SRT are registered trademarks of FCA US LLC.