Go Back   Jeep Garage - Jeep Forum > Jeep Platform Discussion > Grand Cherokee - WJ > Troubleshooting/Problems

Join Jeep Garage Today
Reply
 
Thread Tools Display Modes
 
  #1  
Old 02-22-2011, 03:37 AM
Member
 
Join Date: Feb 2011
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 1415
Mark133 is on a distinguished road
IAT sensor code P0112

I have a 2004 jeep Grand Cherokee Laredo (Altitude pkg), whatever that means, I bought used. It has the 4.0L engine. I have changed the sensor 3 times and back probed the sensor connector and it does send 5.1 volts to the sensor, and the sensor is working, checked it with the repair manual, checked it hot and cold and the range is close to where it should be, I am confident the sensor is working correctly. I had a volt meter on the connector, while turning over the key and the voltage does not jump around, it goes to 5.1 volts and is steady. I want to back probe the connector to the PCM, but don't want to create more problems, and mess up a wire or a 500 dollar PCM. I know the ground wire is common to the ECT and the MAP sensor, my question is would a ground wire problem on either the IAT, ECT or the MAP cause this code to set..? I know it takes 2 low voltage readings in a row to set the code, sometime I get both P0112 and P0113, I just clear with my code reader and sometimes only 1 of them, comes back, seems a bit intermitting to me. I am going to get a PCM flash later this week, and have a tech check for ground wire problems any other ideas..........
__________________

__________________
Reply With Quote
  #2  
Old 02-22-2011, 04:20 AM
Milous's Avatar
Senior Member


 
Join Date: Nov 2009
Location: Nottsure, Wair
Posts: 6,539
Thanks: 36
Thanked 2,305 Times in 963 Posts
Rep Power: 2392929
Milous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond reputeMilous has a reputation beyond repute
Re: IAT sensor code P0112

Here's some info on the two codes that may be helpful:

WJJeeps.com - DTC P0112_P0113
__________________

__________________
Reply With Quote
  #3  
Old 02-22-2011, 04:34 AM
Member
 
Join Date: Feb 2011
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 1415
Mark133 is on a distinguished road
Re: IAT sensor code P0112

Thanks, as part fo your reply it mentioned these also any chance you could post them too.


Refer to the INTERMITTENT CONDITION Symptom
(Diagnostic Procedure).
Perform POWERTRAIN VERIFICATION TEST VER - 5.
__________________
Reply With Quote
  #4  
Old 03-02-2011, 10:49 PM
Member
 
Join Date: Feb 2011
Posts: 16
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 1415
Mark133 is on a distinguished road
Re: IAT sensor code P0112

Just an FYI, I took my Jeep to dealer and he knew exactly what my problem was, 5 min. after he pulled it in and I explained to him what was going on. He reached behind the valve cover where the main wiring harness ran, and it was riding on a bolt back there and had worn a hole in the bottom of the wiring harness and had warn thru it and was wearing a hole thru the IAT power wire, he said that Jeep had ran the wiring harness back between the valve cover and firewall, and he had seen a few of these where it rubs thru the protective wire cover and shorting out some wires, mine just happen to be the IAT wire. Just an FYI, you may be able to pass along....
__________________
Reply With Quote
  #5  
Old 03-03-2011, 12:28 AM
Scottina06's Avatar
JeepGarage Founder
My Jeep: 2014 6.4L SRT8 WK2
 
Join Date: May 2009
Location: Berea, Kentucky
Posts: 49,615
Thanks: 896
Thanked 1,126 Times in 772 Posts
Rep Power: 7718605
Scottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond repute
Garage
Re: IAT sensor code P0112

good find
__________________
SCOTT
The HARDER you work...the LUCKIER you are!
2014 REDLINE red Jeep SRT "BLOODIED\BlackOps CFR Edition" 1 of 1
2013 JKU Wrangler 10A-stormtrooper'ed, JW Speaker and more!
Previous JEEP rides-
2013 Jeep Grand Cherokee SRT-deep cherry
2006 Jeep Grand Cherokee Laredo-inferno red



Twitter-The_Jeep_Guy
Instagram-thejeep_guy

Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
IAT sensor extension AcidCold Performance Modifications 6 03-13-2011 11:37 AM
IAT ohm range? John_R Grand Cherokee - WK 24 03-08-2011 01:43 PM
TPS sensor and Cruise Control sensor dhryan44 Troubleshooting/Problems 15 03-03-2011 01:17 AM
What's that sensor-looking thing? THEPRFCT10 Grand Cherokee - WK2 - 9 01-03-2011 01:09 PM
IAT extension question for BWoody kevin06vino Performance Modifications 22 07-07-2010 01:46 PM

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 04:10 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community

JeepGarage.org is in no way associated with or endorsed by Chrysler Group LLC.