Go Back   Jeep Garage - Jeep Forum > Jeep Platform Discussion > Grand Cherokee - WK

Join Jeep Garage Today
Reply
 
Thread Tools Display Modes
 
  #1  
Old 11-17-2010, 01:43 PM
cherokee619's Avatar
Member
My Jeep: 2005 5.7L WK
 
Join Date: Oct 2010
Location: 757
Posts: 86
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 1487
cherokee619 is on a distinguished road
DTC Question

Well yesterday that it i did plugs and oil change(RP 5w20) it's been going fine but just a little while ago it threw out the check engine and the ob in the dash read code (p0406) can some1 tell me what it means and what could cause it thanks.
__________________

__________________
[SIGPIC][/SIGPIC]
Reply With Quote
  #2  
Old 11-17-2010, 03:10 PM
2005JGC's Avatar
Senior Member


My Jeep: 2005 4.7L WK
 
Join Date: Nov 2010
Location: Portland, OR
Posts: 2,751
Thanks: 51
Thanked 69 Times in 58 Posts
Rep Power: 1652948
2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute2005JGC has a reputation beyond repute
Re: DTC Question

I couldnt get one of the TSB's to open but there were tsb's reguarding a flash for an p0406 (and or other similar egr codes).

P0406 is egr circuit high, so you have an open or short to power somewhere, it may be an update reguarding the pcm's interpretation of what it sees... it may also be a fried egr valve, it could also be wiring too (have to put that in there).
__________________

__________________
Reply With Quote
  #3  
Old 11-19-2010, 08:43 PM
Member
My Jeep: 2006 5.7L WK
 
Join Date: Dec 2009
Location: Home of the Mountain Blue Bird
Posts: 996
Thanks: 0
Thanked 19 Times in 17 Posts
Rep Power: 154907
jeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond repute
Re: DTC Question

Very likely the EGR Valve. Check the connections first though. Could be just a coincidence, but they are a fairly common fail item after about 40K on the clock. Mine went out at about 54K. Have the DTC reset if you can. If it comes back, change the valve. I did that on mine and it came back within a day. No problem since the valve change.
__________________
05 LX/RT & 06 WK/GCO, modded similarly, MDS "ON" Light, Vortex Gens, Debadged, DashHawk, BT Catch Can, SRT CAI W/Add Air Inlet, K&N Filter, Sonnax Trans Press Booster, SC Tuner W/Adv Trans Tuning App, DS Tuner, Cust tube headers w/3 in. catback, Bilsteins, SRT frt/rear bumpers, Eibach SRT Lwr Sprgs & Sways, FRI Sidewinder Cam Adv 2*, 6.1 valvetrain, SLP 25% UD Pulley, BBK 90mm TB, SOS Coils/.060 plug gaps. 20 in. SRT Reps.
Reply With Quote
  #4  
Old 11-19-2010, 11:43 PM
cherokee619's Avatar
Member
My Jeep: 2005 5.7L WK
 
Join Date: Oct 2010
Location: 757
Posts: 86
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 1487
cherokee619 is on a distinguished road
Re: DTC Question

Well today the check eng. light went off, so let's see tomorrow what happends. But next week i'm changing the EGR Valve. Oh btw, can anyone tell if that little plate they sell on 3rd strike that goes between the egr instead of a gasket that it helps lessen the tick on the hemi????
__________________
[SIGPIC][/SIGPIC]
Reply With Quote
  #5  
Old 11-20-2010, 10:25 PM
Member
My Jeep: 2006 5.7L WK
 
Join Date: Dec 2009
Location: Home of the Mountain Blue Bird
Posts: 996
Thanks: 0
Thanked 19 Times in 17 Posts
Rep Power: 154907
jeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond repute
Re: DTC Question

Yours may be on the ragged edge of failing. How many miles on it? If you're going to use a block off plate, you'll still get a light. It needs to have exhaust gas flow through the valve. You'll have to disable it in the PCM (Diablosport Tuner with an older CALID) if you want the plate to work. Then you don't need the valve at all. The new Diablosport Tuner's CALID won't disable it, because it is part of the emission system. That's why the older DS CALID has to be loaded onto the new DS Tuner for it to work. Otherwise the only way to disable it is with a CMR DS tune, which costs mega $$$. Not worth it, IMO.
__________________
05 LX/RT & 06 WK/GCO, modded similarly, MDS "ON" Light, Vortex Gens, Debadged, DashHawk, BT Catch Can, SRT CAI W/Add Air Inlet, K&N Filter, Sonnax Trans Press Booster, SC Tuner W/Adv Trans Tuning App, DS Tuner, Cust tube headers w/3 in. catback, Bilsteins, SRT frt/rear bumpers, Eibach SRT Lwr Sprgs & Sways, FRI Sidewinder Cam Adv 2*, 6.1 valvetrain, SLP 25% UD Pulley, BBK 90mm TB, SOS Coils/.060 plug gaps. 20 in. SRT Reps.
Reply With Quote
  #6  
Old 11-20-2010, 10:44 PM
cherokee619's Avatar
Member
My Jeep: 2005 5.7L WK
 
Join Date: Oct 2010
Location: 757
Posts: 86
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 1487
cherokee619 is on a distinguished road
Re: DTC Question

Quote:
Originally Posted by jeepgcoman View Post
Yours may be on the ragged edge of failing. How many miles on it? If you're going to use a block off plate, you'll still get a light. It needs to have exhaust gas flow through the valve. You'll have to disable it in the PCM (Diablosport Tuner with an older CALID) if you want the plate to work. Then you don't need the valve at all. The new Diablosport Tuner's CALID won't disable it, because it is part of the emission system. That's why the older DS CALID has to be loaded onto the new DS Tuner for it to work. Otherwise the only way to disable it is with a CMR DS tune, which costs mega $$$. Not worth it, IMO.
Oh ok bro. Well it has 98,300k something like that.. yeah i already talked to some shop that does CMR DS TUNE, tooooo! much for what, just to avoid the tick naww..
__________________
[SIGPIC][/SIGPIC]
Reply With Quote
  #7  
Old 11-21-2010, 09:52 PM
Member
My Jeep: 2006 5.7L WK
 
Join Date: Dec 2009
Location: Home of the Mountain Blue Bird
Posts: 996
Thanks: 0
Thanked 19 Times in 17 Posts
Rep Power: 154907
jeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond reputejeepgcoman has a reputation beyond repute
Re: DTC Question

Cherokee619, here's a little info. on the EGR system. Ours is the OBDII type system. Hope this helps a little. This is an old article so the systems today are even more sophisticated.

Understanding Exhaust Gas Recirculation Systems

Posted 11/5/1997
By Henry Guzman


Exhaust gas recirculation (EGR) systems were introduced in the early '70s to reduce an exhaust emission that was not being cleaned by the other smog controls. Oxides of nitrogen (NOx) are formed when temperatures in the combustion chamber get too hot. At 2500 degrees Fahrenheit or hotter, the nitrogen and oxygen in the combustion chamber can chemically combine to form nitrous oxides, which, when combined with hydrocarbons (HCs) and the presence of sunlight, produces an ugly haze in our skies known commonly as smog.

How to reduce NOx NOx formation can be reduced by:
  • Enriching the air fuel (A/F) mixture to reduce combustion temperatures. However, this increases HC and carbon monoxide (CO) emissions.
  • Lowering the compression ratio and retarding ignition timing; but this leads to reduced performance and fuel economy.
  • Recirculating some exhaust gases.
How EGR systems work The EGR valve recirculates exhaust into the intake stream. Exhaust gases have already combusted, so they do not burn again when they are recirculated. These gases displace some of the normal intake charge. This chemically slows and cools the combustion process by several hundred degrees, thus reducing NOx formation.

The design challenge The EGR system of today must precisely control the flow of recirculated exhaust. Too much flow will retard engine performance and cause a hesitation on acceleration. Too little flow will increase NOx and cause engine ping. A well-designed system will actually increase engine performance and economy. Why? As the combustion chamber temperature is reduced, engine detonation potential is also reduced. This factor enabled the software engineers to write a more aggressive timing advance curve into the spark timing program. If the EGR valve is not flowing, onboard diagnostics (OBD) systems will set a code and the power control module (PCM) will use a backup timing curve that has less advance to prevent engine ping. Less timing advance means less performance and economy. Do your customer a favor and fix those EGR codes that you may have previously deemed as unimportant.
Evolution of the EGR systems The first EGR valves appeared in 1973 on GM cars. Bolted to the intake manifold next to the carburetor, it has ports to the intake and exhaust manifolds. It has a diaphragm that pulls open a valve stem, which allows exhaust to enter the intake manifold when ported vacuum is applied to it. Ported vacuum increases with throttle opening. A thermal vacuum switch prevents vacuum from reaching the EGR during cold engine starts. This system had many problems. It would often open too soon or too much, which caused a hesitation on acceleration as massive amounts of recirculated exhaust hit the combustion chamber. Many people simply disconnected it when it began to cause problems because they did not understand its importance or design. By 1975, if you unplugged an EGR valve, you'd have a driveability complaint of engine ping. Manufacturers and technicians of that era experimented with vacuum orifice restrictors and vacuum delay valves to try to find a happy medium between clean air and performance.
Closed loop systems By 1981, closed loop computer controls were in place. EGR flow was now more carefully controlled with dual diaphragm and back-pressure EGR valves. Modulating the vacuum to the EGR valve's pull, open diaphragm controlled the flow of recirculated ex- haust. Called by various names such as amplifiers, transducers and modulators, both remote and integral vacuum modulated devices were used. The flow of vacuum was further controlled by solenoids that blocked the vacuum ports until certain criteria were met such as engine temperature, rpm and manifold absolute pressure (MAP).
As the manufacturers began to use these complex schemes with vacuum amplifiers, delay valves and solenoids, they added a lot of "spaghetti" to the engine compartment. Plastic vacuum connections would break and rot with age and were not very reliable. Vacuum diagrams were invented and became essential to the smog driveability technicians of the day. As these systems evolved, they had fewer parts and less vacuum tubing. This was achieved by the use of pulse width modulated EGR solenoids. The PCM controlled EGR flow through the use of these solenoids to modulate vacuum to the EGR valve instead of just turning it on or off periodically.
What is pulse width modulation? Let's take a moment to discuss how computers think so we can better understand this common form of PCM control. Computers are binary. The machine language they operate in consists of only two variables: on or off, true or false, high or low. That's the only way a PCM can think. As a result, computer controlled outputs are always on or off, high (system voltage) or low (ground). Therefore, a computer output is always a square wave, or an on-off step when viewed on a lab scope. The high portion of the waveform will usually be battery voltage or PCM voltage of approximately 5 volts, with a few exceptions where the PCM operates at a different voltage.
Once the PCM receives its inputs, such as rpm, throttle angle, coolant temperature and MAP, it then calculates a response based on the software program that is embedded into it. Next, it makes its decision and sends a command in the form of a pulse width modulated signal to turn the EGR solenoid on and off rapidly. The EGR solenoid has two vacuum nipples. One side gets either manifold or ported engine vacuum. The other nipple goes to the EGR valve. Its default position is to block vacuum to the EGR valve. A vent is incorporated to bleed off vacuum when the solenoid is being pulsed. Vacuum flows to the EGR in rapid on-off pulses as the solenoid is commanded by the PCM.
OBD I systems With each succeeding year, the EGR designs became more refined. The California Air Resources Board (CARB) liked GM and Chrysler's onboard diagnostic systems. In 1988, CARB required that all cars sold in California be equipped with an onboard diagnostic system and a "check engine" light to notify the driver of emission system failure. By this time, all manufacturers had to have an EGR system that was capable of alerting the driver if it was not working. OBD I diagnostics and trouble codes were added in to flag opens, shorts and sticking solenoids.
OBD II EGR systems OBD II requires that the EGR system be monitored for abnormally low or high flow rate malfunctions. The EGR is considered malfunctioning when an EGR component fails or a fault in the flow rate results in the vehicle exceeding the Federal Test Procedure (FTP) by 1.5 times. FTP is the government-mandated drive cycle smog test that all new cars must pass and adhere to.

The diagnostic executive, also called the diagnostic task manager by Chrysler, controls the EGR monitor. The executive is an OBD II software agent given the task of managing all the onboard monitors and the scan tool interface. The executive coordinates the sequencing and actuation of all the monitor's test routines. There are eight main monitors whose sole function is to directly monitor and test the components assigned to them to ensure they meet FTP standards for life. These monitors are:
  • Catalyst monitor
  • EGR monitor
  • EVAP monitor
  • Fuel system monitor
  • Misfire monitor
  • Oxygen monitor
  • Oxygen heater monitor
  • Secondary air injection monitor
A closer look at the EGR monitor Monitor tests are both intrusive and non-intrusive. An example of an intrusive test is when the EGR monitor cycles the EGR valve during a condition when it normally would be closed. In some cases, the customer may feel an intrusive test as a slight miss.


The method of testing used by the EGR monitor varies according to the manufacturer, but there are three main types.
One method includes looking for a change in manifold pressure as the EGR valve is actuated on and off.

A second method involves cycling the EGR valve and looking for a change in short-term fuel trim. When the EGR valve is opened, it displaces some of the air fuel mixture. When the EGR valve is closed, more oxygen enters the combustion chamber, which then leans the mixture somewhat. The O2 sensor will respond with a lean signal to the PCM, which in turn increases pulse width. This is called short-term fuel trim compensation. The EGR monitor looks to see that all these things are occurring as they should. It repeats the tests and averages the results. Before the EGR monitor can begin its testing, it must first receive clearance from the diagnostic executive. The executive ensures that there are no conflicting conditions that would invalidate the EGR monitor's tests. For example, if the car had a lazy O2 sensor, fuel trim compensation to the EGR opening and closing would be inaccurate. Therefore, there are many safeguards built into OBD II to prevent this type of occurrence from happening. OBD II also has rationality checks. In other words, it uses deductive logic and constantly compares its inputs against each other to make sure all are in sync with one another. After the EGR monitor gets the OK to run its tests, it uses strict enabling criteria to ensure accurate testing such as:
  • Engine temperature more than 170 F.
  • Ambient air temperature more than 20 F.
  • Engine run time more than three minutes since 170 F.
  • Engine speed 2248-2688 (auto. trans.), 1952-2400 (manual trans.).
  • Manifold absolute pressure from 5-20 hg.
  • Short Term Adaptive Fuel Trim is adjusting pulse width by less than +7 percent and more than -8 percent.
  • TP sensor from 0.6 to 1.8 volts.
  • Vehicle speed sensor more than 40 mph.
The above is used for illustrative purposes only. Refer to your manual or CD-ROM information system for specifics to the car you are working on.

The third type of EGR monitoring design includes monitoring an EGR position sensor and a back-pressure sensor. Some Fords use a differential pressure feedback sensor that reads exhaust back-pressure upstream and downstream of the EGR valve to determine its flow rate and operation.
While OBD I systems would usually flag an inoperative EGR system, OBD II systems are given the task of determining the correct amount of EGR flow to keep the car running clean.
Next month, we will get into diagnosis, testing and repair techniques for all the different types of EGR systems. I will also cover pattern failures of all types, including mechanical problems such as plugged EGR passages that can cause rpm specific misfire concerns. Henry Guzman is an ASE master tech with L1 certification. He has 20 years of experience working as a technician on foreign and domestic cars.
__________________

__________________
05 LX/RT & 06 WK/GCO, modded similarly, MDS "ON" Light, Vortex Gens, Debadged, DashHawk, BT Catch Can, SRT CAI W/Add Air Inlet, K&N Filter, Sonnax Trans Press Booster, SC Tuner W/Adv Trans Tuning App, DS Tuner, Cust tube headers w/3 in. catback, Bilsteins, SRT frt/rear bumpers, Eibach SRT Lwr Sprgs & Sways, FRI Sidewinder Cam Adv 2*, 6.1 valvetrain, SLP 25% UD Pulley, BBK 90mm TB, SOS Coils/.060 plug gaps. 20 in. SRT Reps.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
service 4wd light with no dtc? boss_hemi Grand Cherokee - WK 6 10-04-2010 11:17 AM
Dtc c140f wmassWK Grand Cherokee - WK 4 09-21-2010 09:58 AM
Dtc u 1418 Kruzy Grand Cherokee - WK 5 01-04-2010 10:49 PM
DTC REPORT P 0440, what does that mean??? White WK Swagga Troubleshooting/Problems Discussion 23 11-15-2009 01:19 AM
DTC Code C141D LTrainGC Troubleshooting/Problems Discussion 14 07-22-2009 06:49 AM

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 06:23 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community