Go Back   Jeep Garage - Jeep Forum > Modifications & Enhancements > Performance Modifications

Join Jeep Garage Today
Reply
 
Thread Tools Display Modes
 
  #1  
Old 09-16-2009, 05:00 PM
mzh29's Avatar
Premium Member
 
Join Date: Jun 2009
Location: Germantown, Md
Posts: 679
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 2737
mzh29 has a reputation beyond reputemzh29 has a reputation beyond reputemzh29 has a reputation beyond repute
Can someone explain timing to me?

Just as the title says, enlighten me. I get 32 degrees of timing while coasting at highway speeds. Then when I hit it, it drops to about 17-20 degrees timing. What does this mean? Thanks!
__________________

__________________
Jeep is gone, lots of good memories, lots of turned heads. Now driving a 2013 Charger RT blacktop!
Reply With Quote
  #2  
Old 09-16-2009, 05:12 PM
Marlin's Avatar
"The Aussie"

My Jeep: 1981 5.7L CJ
 
Join Date: May 2009
Location: Licmye Bawlls
Posts: 9,362
Thanks: 65
Thanked 17 Times in 16 Posts
Rep Power: 81093
Marlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond repute
Re: Can someone explain timing to me?

Wiki - Ignition timing, in a spark ignition internal combustion engine, is the process of setting the time that a spark will occur in the combustion chamber (during the power stroke) relative to piston position and crankshaft angular velocity.


Me - So, when you're on a light throttle cruise, timing is advanced. every engine behaves differently, but basically, because there is little air and fuel required to "coast", timing can be advanced more to make the burn more efficient.
When you nail the throttle, more fuel and air enters the engine, and timing needs to be backed off otherwise "pre-ignition" will occur. Basically this means that if the spark happens too early, with the piston still travelling up the bore on the compression stroke, the air/fuel will ignite too early, and will try and send the piston back down (very violently!) before it has made its way all the way to the top.
__________________

__________________
Reply With Quote
  #3  
Old 09-16-2009, 05:13 PM
blackpepper's Avatar
Senior Member
My Jeep: 2009 6.1L WK
 
Join Date: May 2009
Location: SF Bay Area
Posts: 6,435
Thanks: 67
Thanked 39 Times in 28 Posts
Rep Power: 13555
blackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond reputeblackpepper has a reputation beyond repute
Re: Can someone explain timing to me?

I can't.. but this guy can .. and so can Ben

By Michael Shiffer http://www.type2.com/library/electrip/timex.htm

"There has been a lot of mail concerning how to set timing with an unknown engine. I think a basic description of timing might help sort out a lot of this. First, you should know that there are two types of timing in an engine: cam timing and ignition timing. (Three types, if you count injector pulse, but injection timing on gasoline-powered busses is tied to ignition timing and is not separately adjustable so I will ignore it, as should you.) Cam timing is what determines when the valves open and close with respect to the position of the pistons in their bores. It is set when the engine is built- by placing the camshaft and crankshaft in the correct relationship. It cannot be adjusted on a stock engine. It doesn’t change: if it was right once it will be right for the life of the engine, barring disaster. And by disaster I mean the park-it-where-stops-rolling kind of disaster. (This is a very rare occurrence in VW air-cooled engines. Not so rare in the Rabbit/Golf ones, which drive the cam with a rubber belt which strips if you don’t change it on schedule.) In sum: cam timing is not connected with or affected by turning the distributor. What distributors time is spark, or ignition. Why?

At idle, your engine is turning relatively slowly, let’s say 1000 rpms. The throttle is closed, so very little fuel and air are being drawn in to the cylinders. This small amount of combustible mixture burns very quickly, so for maximum efficiency, the spark needs to start when the piston is very near top dead center. If the spark comes too early (too advanced), the pressure from the ignited mixture will hit the piston while it is still coming up the cylinder and be wasted trying to shove the piston down before it reaches the end of it’s travel. If you try to start an engine whose ignition timing is too advanced, the starter will try to turn the crank one way, and the combustion process will try to turn it the other way, and it will seem as if the starter hasn’t enough oomph to start it. Contrariwise, if the timing is set too late (too retarded), the pressure from the ignited mixture (and the power derived therefrom) will dissipate as the flame front chases the piston down the cylinder bore in the rapidly diminishing pressure of the combustion chamber. In other words, the piston is already on it’s way towards the bottom of it’s stroke, reducing the effectiveness of combustion. The is very fuel inefficient, since a larger throttle opening at idle (set by the idle speed screw) is needed allow extra fuel in to keep the engine idling. In practical terms, the position of the distributor which yields the highest idle speed is within a very few degrees of where it should be set. (If you retard the timing about 5 degrees from this point, you will be awfully close to spot-on.) Of course, this assumes your carburetor (or F.I.)is working well and that the idle mixture is correct.

When driving on the highway, your engine’s timing requirement is different. At higher engine speeds, larger throttle openings and greater loads than idle, you need ignition advance. There are two reasons for this. First, you are burning more fuel so complete combustion takes longer. Second, the combustion time, as a percentage of the time the piston is at or near top dead center is much longer because of the piston speed. What this means is that you have to ignite the charge earlier, while the piston is still coming up, in order to get the full benefit of the pressure against the piston at the right time. Too early or too late timing will have a similar effect at speed as at idle, but greatly magnified and with far more destructive potential. Too retarded timing will give low power, lousy emissions and excessive bore wear. Timing too advanced will cause pinging (a rattling noise usually heard on acceleration), overheating cylinder heads and other problems too scary to contemplate.

I will now pretend that vacuum advance doesn’t exist. It will only confuse things.

Distributors have little weights inside that swing away from the shaft as it turns faster. As they move out, they rotate the upper part of the shaft which passes through the plate that the points are bolted to so that the rubbing block which opens the points meets the lobes which hit it (and thus open the points) a little earlier. At what engine speed this advance begins, at what rate it advances and at what engine speed it stops advancing is determined by the shape and mass of the advance weights and the strength of their return springs; at what degree of advance it stops is determined by a limiter on the plate to which the weights are bolted . None of this is meant to be adjusted: the manufacturer sets it up for each engine family it builds, based on compression, cam profile, octane requirements and availability, among other things. Timing the ignition, then, is a matter of getting the timing correct at one end (idle or full advance) and letting the rest of the range look after itself.

If you have a stock distributor and know either the timing at idle or the maximum advance at a given engine speed and you have a good timing light, you will have no trouble setting timing. If not, here are some ways to get in the ball park. I already mentioned that the highest idle speed is very slightly advanced from correct. If you set it there and hear no pinging on acceleration and get good power (ha-ha), you are good. If it pings, retard it little by little until the pinging goes away. If it seems weak, advance the timing a little at a time until you hear pinging or find the engine hard to start, then retard it again. "
__________________
Ryan
2009 SRT8 - loaded, corsa exhaust, afe stage ii intake, diablo intune w/ Johan toona, vreds 275/315, r1 drilled/slotted rotors, stoptech pads, lockpick adapter, billet tech catch can, 180 tstat, eibach springs, bwoody links, stage 6 qa1 shocks, tail light tint, front window tint, stillen hl brows, lloyd mats, powder-coated alcoas, red srt lettering, trim color-matched...

2007 Jeep 5.7 Limited - 120,681 miles, one owner. SOLD
Reply With Quote
  #4  
Old 09-16-2009, 05:14 PM
psycojeep's Avatar
Member
My Jeep: 2006 5.7L WK
 
Join Date: Jun 2009
Location: Spokane, Wa
Posts: 459
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 2497
psycojeep has a reputation beyond reputepsycojeep has a reputation beyond repute
Re: Can someone explain timing to me?

Timing is the time that a spark will occur in the combustion chamber (during the power stroke) relative to piston position and crankshaft angular velocity.
__________________
2006 Inferno Red Overland

"Spend money I don't have, on things I don't need, to impress people I don't know"


"Anyone can restore them, it takes a real man to cut one up"
Reply With Quote
  #5  
Old 09-16-2009, 05:28 PM
mzh29's Avatar
Premium Member
 
Join Date: Jun 2009
Location: Germantown, Md
Posts: 679
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 2737
mzh29 has a reputation beyond reputemzh29 has a reputation beyond reputemzh29 has a reputation beyond repute
Re: Can someone explain timing to me?

Awsome thanks guys, makes sense to me. Does that timing seem about normal for our motors? about 17* at WOT?
__________________
Jeep is gone, lots of good memories, lots of turned heads. Now driving a 2013 Charger RT blacktop!
Reply With Quote
  #6  
Old 09-16-2009, 05:33 PM
Marlin's Avatar
"The Aussie"

My Jeep: 1981 5.7L CJ
 
Join Date: May 2009
Location: Licmye Bawlls
Posts: 9,362
Thanks: 65
Thanked 17 Times in 16 Posts
Rep Power: 81093
Marlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond reputeMarlin has a reputation beyond repute
Re: Can someone explain timing to me?

Yeah pretty standard
__________________
Reply With Quote
  #7  
Old 10-01-2009, 10:41 AM
Member
 
Join Date: Sep 2009
Location: Colombia S. America
Posts: 64
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 1997
justa4banger is a glorious beacon of light
Re: Can someone explain timing to me?

One thing to remember about timing.. EVERY ENGINE is different, your total timing at WOT is 17* Some 4.6 V8 mustangs are at 22*, my little 4 cyl mustang with turbo was at 29* total timing.
So never try to compare timing between different engines, and really even same engines can have variances.

One thing to remember is generally the less effecient the engine the more timing needed... So for instance my 4 pot mustang runs on 29* total timing, well first off this wasn't pump 93 friendly, nor was the 28psi of boost i shoved down the intake, but if i had the same setup and boost on a Aluminum head versus my cast iron head, it would only need around 22* total timing @WOT.
Now would the less timing yield more power.. no, but i might be able to get damn near the same power with less risk of detonation..

At light cruise on the freeway my mustang will go up to 52* of total timing (light load coasting)... my old 1970's designed engine just isn't as efficient as it could be.
__________________
2007 GC CRD w/ Inmotion Tune
267whp/425wtrq
Reply With Quote
  #8  
Old 10-01-2009, 10:46 AM
FlyinRyan's Avatar
Senior Member
My Jeep: 2002 4.7L WJ
 
Join Date: Jul 2009
Location: Fort Myers, Florida
Posts: 2,804
Thanks: 33
Thanked 31 Times in 30 Posts
Rep Power: 88720
FlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond reputeFlyinRyan has a reputation beyond repute
Send a message via AIM to FlyinRyan
Re: Can someone explain timing to me?

Quote:
Originally Posted by mzh29 View Post
Awsome thanks guys, makes sense to me. Does that timing seem about normal for our motors? about 17* at WOT?
I see that you have superchips. On a 87 file, yes this is normal.
__________________
Due to my workload, please do not PM me as I do not regularly check my PMs. Thank you :)
Reply With Quote
  #9  
Old 10-01-2009, 04:38 PM
mzh29's Avatar
Premium Member
 
Join Date: Jun 2009
Location: Germantown, Md
Posts: 679
Thanks: 0
Thanked 0 Times in 0 Posts
Rep Power: 2737
mzh29 has a reputation beyond reputemzh29 has a reputation beyond reputemzh29 has a reputation beyond repute
Re: Can someone explain timing to me?

Quote:
Originally Posted by Sleepy4.7 View Post
I see that you have superchips. On a 87 file, yes this is normal.
I am using the 91 octane tune with 93 gas.
__________________

__________________
Jeep is gone, lots of good memories, lots of turned heads. Now driving a 2013 Charger RT blacktop!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
timing 06GRAND4.7 Performance Modifications 30 09-10-2009 08:15 PM

Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 05:17 AM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community

JeepGarage.org is in no way associated with or endorsed by Chrysler Group LLC.