SRT Part numbers - Help! (Belly pan) - Jeep Garage - Jeep Forum

Go Back   Jeep Garage - Jeep Forum > Jeep Platform Discussion > Grand Cherokee SRT - WK2

Reply
 
Thread Tools Display Modes
 
  #1  
Old 12-01-2015, 08:06 PM
Lankness's Avatar
Premium Member
 
Join Date: Aug 2011
Location: Pearland, TX
Posts: 1,097
Thanks: 115
Thanked 191 Times in 131 Posts
Rep Power: 1148729
Lankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond repute
SRT Part numbers - Help! (Belly pan)

After the recent work on the Jeep my front belly pan missing. I'm looking for the part numbers and pricing that I would need to replace it. The best description that I have is from this resource: http://wk2jeeps.com/pdf/2014_2016_wk...mp_removal.pdf

Page 3 outlines the removal. In short, I am missing the following:
1. Black plastic belly pan
2. Several fasteners across the front that attach to the bottom of the front clip. I seem to recall that these are silver bolts that have approximately 10mm heads. These are in the above pdf as push pins but I seem to recall there being bolts under there I had to wrench off as well.
3. 2 fasteners at the back to the cross member. I believe these are the same 10mm bolts.
4. Push pin at the rear center of the belly pan that attaches to the cross member between the fasteners listed at #3 above.
5. Several fasteners for the fender liners. These are black screws that are approximately 7mm heads.

I have plastic rivets that are required for some of the connections of the fender wheel and the front clip. However, it was also returned missing the connectors that are at the top edge of the front clip and actual fender on each side. These are listed in step 6 of the SRT removal of the above pdf. If anyone has removed the front clip you will know how much of a PITA these 2 connectors are (especially getting them back on). I would also like to replace the left and right fastener there.

Would anyone be able to provide some insight as to the part numbers required for the above? I've checked with a few dealers and JFJs, but am having trouble getting any positive results.

And yes, I know I could go get bolts/screws from the hardware store, but I'd prefer to get OEM stuff for everything.

Thanks.

__________________
-------------------------
Kevin

2014 Max Steel GC SRT, built by the bad boys at JNAP .
Livernois built 392 and Whipple Kit
Reply With Quote
Sponsored Links
Advertisement
 
  #2  
Old 12-01-2015, 08:10 PM
Jsboening's Avatar
Senior Member
My Jeep: 2015 6.4L SRT WK2
 
Join Date: Nov 2014
Location: Rockford, MI
Posts: 1,164
Thanks: 195
Thanked 288 Times in 221 Posts
Rep Power: 2736
Jsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond reputeJsboening has a reputation beyond repute
Re: SRT Part numbers - Help! (Belly pan)

You may be able to find the parts you need using this website. http://www.mopar.com/jeep/grand-cherokee/2014/


Sent from my iPhone using JeepGarage
Reply With Quote
The Following User Says Thank You to Jsboening For This Useful Post:
  #3  
Old 12-01-2015, 08:18 PM
Scottina06's Avatar
JeepGarage Founder
My Jeep: 2014 6.4L SRT8 WK2
 
Join Date: May 2009
Location: Berea, Kentucky
Posts: 54,024
Thanks: 2,452
Thanked 2,827 Times in 1,753 Posts
Rep Power: 7791176
Scottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond reputeScottina06 has a reputation beyond repute
Garage
Re: SRT Part numbers - Help! (Belly pan)

if you don't find it online..call justforjeeps and ask for correy
__________________
SCOTT
The HARDER you work...the LUCKIER you are!
2014 REDLINE red Jeep SRT "BLOODIED" 1 of 1
2013 JKU Wrangler 10A-stormtrooper'ed, JW Speaker and more!
Previous JEEP rides-
2013 Jeep Grand Cherokee SRT-deep cherry
2006 Jeep Grand Cherokee Laredo-inferno red



Twitter-The_Jeep_Guy
Instagram-thejeep_guy

Reply With Quote
The Following User Says Thank You to Scottina06 For This Useful Post:
Sponsored Links
Advertisement
 
  #4  
Old 12-01-2015, 08:31 PM
Premium Member
My Jeep: 2015 6.4L SRT WK2
 
Join Date: Apr 2015
Location: bartlett,il
Posts: 135
Thanks: 14
Thanked 40 Times in 32 Posts
Rep Power: 938
hemirt is on a distinguished road
Re: SRT Part numbers - Help! (Belly pan)

Hi Lankness, i think you are looking for the bolts that hold the brake ducting on, there are 7-10 mm bolts at the front along with 5 push pins, these are silver...there are 3-8mm black screws at each corner of the duct panel that attach to the wheel well lining, and then there are 2- 13mm bolts along with a large push pin on the metal shield,these are silver, i just had mine off to install the XLUME badge in the lower grill
Reply With Quote
The Following 2 Users Say Thank You to hemirt For This Useful Post:
  #5  
Old 12-01-2015, 08:48 PM
Lankness's Avatar
Premium Member
 
Join Date: Aug 2011
Location: Pearland, TX
Posts: 1,097
Thanks: 115
Thanked 191 Times in 131 Posts
Rep Power: 1148729
Lankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond repute
Re: SRT Part numbers - Help! (Belly pan)

Quote:
Originally Posted by hemirt View Post
Hi Lankness, i think you are looking for the bolts that hold the brake ducting on, there are 7-10 mm bolts at the front along with 5 push pins, these are silver...there are 3-8mm black screws at each corner of the duct panel that attach to the wheel well lining, and then there are 2- 13mm bolts along with a large push pin on the metal shield,these are silver, i just had mine off to install the XLUME badge in the lower grill
Sounds about right. It's been nearly 11 months since I took it off and put it back on the last time, so my memory is fuzzy. I do have some empty Ziplocs though labeled 'Belly pan'
__________________
-------------------------
Kevin

2014 Max Steel GC SRT, built by the bad boys at JNAP .
Livernois built 392 and Whipple Kit
Reply With Quote
  #6  
Old 12-01-2015, 09:21 PM
Member
My Jeep: 2013 6.4L SRT8 WK2
 
Join Date: Jan 2011
Location: Laguna Beach, CA
Posts: 505
Thanks: 22
Thanked 85 Times in 62 Posts
Rep Power: 8035
Carbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond repute
Garage
Re: SRT Part numbers - Help! (Belly pan)

2014 JEEP GRAND CHEROKEE 4x4 STR8, 6.4L V8 SRT HEMI MDS, 8-Spd Auto 8HP70 Trans (Buy) Underbody Shields And Plate

Try this page out, might help...
Reply With Quote
The Following User Says Thank You to Carbon6 For This Useful Post:
  #7  
Old 12-02-2015, 07:26 AM
Lankness's Avatar
Premium Member
 
Join Date: Aug 2011
Location: Pearland, TX
Posts: 1,097
Thanks: 115
Thanked 191 Times in 131 Posts
Rep Power: 1148729
Lankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond repute
Re: SRT Part numbers - Help! (Belly pan)

I had found 2 parts listed for the belly pan, that one shows 4 (part 14).
14 68091772AA BELLY PAN. Front. . [EHD] Or [ERB], [ERB].
BELLY PAN. Front. [ERB].
ST. . Required: 001 $67.65 68091772AA
14 68089029AC BELLY PAN. Front. . [ESG].
BELLY PAN. Front. [ESG].
ST. . Required: 001 $190.40 68089029AC
14 68037063AD BELLY PAN. Front. . [EX0], [EXF].
BELLY PAN. Front. [EXF].
ST. . Required: 001 $90.98 68037063AD
14 55079191AD BELLY PAN. Front. . [EZH].
BELLY PAN. Front. [EZH].
ST. . Required: 001 $62.42 55079191AD

Any ideas? I'm going to go ahead and assume that the priciest will be the SRT piece, but will certainly verify with the dealer first.
__________________
-------------------------
Kevin

2014 Max Steel GC SRT, built by the bad boys at JNAP .
Livernois built 392 and Whipple Kit
Reply With Quote
  #8  
Old 12-02-2015, 11:05 AM
Member
My Jeep: 2013 6.4L SRT8 WK2
 
Join Date: Jan 2011
Location: Laguna Beach, CA
Posts: 505
Thanks: 22
Thanked 85 Times in 62 Posts
Rep Power: 8035
Carbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond reputeCarbon6 has a reputation beyond repute
Garage
Re: SRT Part numbers - Help! (Belly pan)

Quote:
Originally Posted by Lankness View Post
I had found 2 parts listed for the belly pan, that one shows 4 (part 14).
14 68091772AA BELLY PAN. Front. . [EHD] Or [ERB], [ERB].
BELLY PAN. Front. [ERB].
ST. . Required: 001 $67.65 68091772AA
14 68089029AC BELLY PAN. Front. . [ESG].
BELLY PAN. Front. [ESG].
ST. . Required: 001 $190.40 68089029AC
14 68037063AD BELLY PAN. Front. . [EX0], [EXF].
BELLY PAN. Front. [EXF].
ST. . Required: 001 $90.98 68037063AD
14 55079191AD BELLY PAN. Front. . [EZH].
BELLY PAN. Front. [EZH].
ST. . Required: 001 $62.42 55079191AD

Any ideas? I'm going to go ahead and assume that the priciest will be the SRT piece, but will certainly verify with the dealer first.
They all show to fit the 2014 SRT, would probably have to either call the dealer, Just for Jeeps, or ask Milous but its funny that it could either be the $67.xx dollar part or the $190.xx dollar part...
Reply With Quote
  #9  
Old 12-02-2015, 12:41 PM
Lankness's Avatar
Premium Member
 
Join Date: Aug 2011
Location: Pearland, TX
Posts: 1,097
Thanks: 115
Thanked 191 Times in 131 Posts
Rep Power: 1148729
Lankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond reputeLankness has a reputation beyond repute
Re: SRT Part numbers - Help! (Belly pan)

Quote:
Originally Posted by Carbon6 View Post
They all show to fit the 2014 SRT, would probably have to either call the dealer, Just for Jeeps, or ask Milous but its funny that it could either be the $67.xx dollar part or the $190.xx dollar part...
Yea, the AC part is the SRT-specific one. ESG is the code for the SRT engine (Engine/Transmission 1: (Standard) 6.4L V8 SRT HEMI MDS ENGINE (ESG) + 8-SPD AUTO 8HP70 TRANS (DFD) = Package 29L - thanks to Milious' site!)

Shocking
__________________
-------------------------
Kevin

2014 Max Steel GC SRT, built by the bad boys at JNAP .
Livernois built 392 and Whipple Kit
Reply With Quote
Reply

Tags
SRT

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Similar Threads
Thread Thread Starter Forum Replies Last Post
Belly Pan Cover V8 silvermax04 Grand Cherokee - WK2 - 5 07-18-2013 08:56 PM
Belly Armor & Rocker Panel Protection Recommendations CWRUYOTE Off Road Modifications 0 04-17-2013 08:28 PM
Ask for info on rear belly pan Suther Grand Cherokee SRT - WK2 1 09-12-2012 08:05 PM
OEM Srt springs part numbers.. Bigdiesel74 Grand Cherokee - WK 1 04-04-2010 02:47 AM

» Premium Vendor Showcase
Powered by vBadvanced CMPS v3.2.3

All times are GMT -5. The time now is 12:32 PM.


Powered by vBulletin® Version 3.8.8
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community

JeepGarage.org is in no way associated with or endorsed by FCA US LLC. Chrysler, Dodge, Jeep, Ram, Mopar and SRT are registered trademarks of FCA US LLC.