Jeep Garage  - Jeep Forum

Jeep Garage - Jeep Forum (http://www.jeepgarage.org/forums.php)
-   Grand Cherokee - WK (http://www.jeepgarage.org/f5/)
-   -   HELP !Airaid Throttle body spacer + Powerwire Problems!!! (http://www.jeepgarage.org/f5/help-airaid-throttle-body-spacer-powerwire-problems-11590.html)

romel80 08-02-2010 12:27 PM

HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
hello everyone,

i have a 05 3.7 Laredo, i installed the airaid throttle body spacer but the cruise and throttle cables need some adjustments so that the throttle can close and open normally. does anyone know how to do these adjustments?? ( Note i installed the bracket as instructed but still need about 1 inch for the throttle to close completely). I hope anyone could help.

i bought too the airram powerwire, but i didnt know where to install it, i recognized that at one end the air intake tube but the second end was not known to me. Can anyone help and tell me where to install both ends of the powerwire?

thanks a lot

Escape 08-02-2010 12:47 PM

Re: HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
Remove the throttle body spacer and your problem is solved. It doesn't do anything for your engine.

As for the powerwire I have no idea...someone with one will have to post up.

Scottina06 08-02-2010 12:57 PM

Re: HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
unplug the iat wire....one end plugs into the iat sensor on the intake tube and the other end into the iat wire

romel80 08-02-2010 02:02 PM

Re: HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
thank you guys,
but what is the iat wire and where it is located? i found the sensor attached to the intake tube, but the other end of the wire still didnt find it:mad:

Escape 08-02-2010 02:27 PM

Re: HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
iat = Intake air temperature

it's the sensor attached to your intake tube that you found.

I believe what Scott is saying is to unplug the electrical connection going to the sensor and place the powerwire inbetween the wire and the sensor.

right now you have iat wire, iat sensor.
in the end you will have iat wire, powerwire, iat sensor.

romel80 08-02-2010 02:32 PM

Re: HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
you men i connect one harness of the powerwire to the sensor on the cold air intake tube and the other end to the wire that was already connected to the sensor????

romel80 08-02-2010 02:42 PM

Re: HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
thank you escape and scott for your help :) Bless you guys

Milous 08-02-2010 05:03 PM

Re: HELP !Airaid Throttle body spacer + Powerwire Problems!!!
 
Quote:

Originally Posted by Escape (Post 245779)
Remove the throttle body spacer and your problem is solved. It doesn't do anything for your engine.

As for the powerwire I have no idea...someone with one will have to post up.

Agreed. Both are snakeoil products.


All times are GMT -5. The time now is 11:49 AM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community