Jeep Garage  - Jeep Forum

Jeep Garage - Jeep Forum (http://www.jeepgarage.org/forums.php)
-   Troubleshooting/Problems (http://www.jeepgarage.org/f203/)
-   -   Key Stuck In Ignition Request For Help (http://www.jeepgarage.org/f203/key-stuck-in-ignition-request-for-help-33595.html)

Milo 01-06-2012 12:36 AM

Key Stuck In Ignition Request For Help
 
Hello Everybody

I have a 2002 Jeep Grand Cherokee Lerado, 4.7 V8 with 95,000 miles.

Problem: Upon parking and turning the engine off, I am unable to turn the key to the natural position where I can remove the key from the ignition. I have the Jeep in park and foot on the break while doing this. In order to get the key out of the ignition, I have to turn the key back one position toward the start position (not starting the engine), pump the breaks and cycle the shifter through all the gears and back into park a few times. This doesn’t happen every time I drive the Jeep, but it’s occurring more frequent.

I assume there is some linkage between the gear shifter, break, and ignition that is to blame. If any of you have information on how to fix this, I would be deeply appreciative!

Note: Yesterday I tried to start the Jeep by turning the ignition key and the starter would not activate. The dash lights, radio, and other electrical come online, but no starter. This was the first time I have encountered this problem. Not sure if it’s related to my key stuck in the ignition or not.

Thank You!

SvenskaJeepGuy 01-06-2012 03:32 AM

Re: Key Stuck In Ignition Request For Help
 
looks like the ignition, i had to replace it in my WJ as well.

Milo 05-09-2012 03:36 PM

Re: Key Stuck In Ignition Request For Help
 
Quote:

Originally Posted by Milo (Post 546637)
Hello Everybody

I have a 2002 Jeep Grand Cherokee Lerado, 4.7 V8 with 95,000 miles.

Problem: Upon parking and turning the engine off, I am unable to turn the key to the natural position where I can remove the key from the ignition. I have the Jeep in park and foot on the break while doing this. In order to get the key out of the ignition, I have to turn the key back one position toward the start position (not starting the engine), pump the breaks and cycle the shifter through all the gears and back into park a few times. This doesn’t happen every time I drive the Jeep, but it’s occurring more frequent.

I assume there is some linkage between the gear shifter, break, and ignition that is to blame. If any of you have information on how to fix this, I would be deeply appreciative!

Note: Yesterday I tried to start the Jeep by turning the ignition key and the starter would not activate. The dash lights, radio, and other electrical come online, but no starter. This was the first time I have encountered this problem. Not sure if it’s related to my key stuck in the ignition or not.

Thank You!

Update:

Per my earlier post, I found and fixed the key and start problems.

Back in January I was experiencing a problem where I wasn't able to turn the key to the natural position where the key can be removed from the ignition. This was due to the binding of parts within the shift mechanism.

Understanding how it works: There is a cable that runs from the gear shifter to the ignition/key in the steering column. This cable prevents the ignition key from being removed unless the shifter is in park. In addition there is a solenoid that prevents the button on the shifter from being depressed unless your foot is on the break. The cap on the solenoid has a hole where a metal bar connects the solenoid to the button linkage.

The Problem: The cap on this solenoid had come loose, slid down the metal bar, and was binding between the bar and metal shifter base.

The Fix: Just slide the cap back on the solenoid and snap it into place. Maybe a little glue on the cap to prevent it from coming louse again. I placed some grease on the metal bar to reduce friction between the bar and solenoid cap.

Solenoid location: The solenoid is located under the tray that is located between the shifter and ash tray, or hole between the seat heater switches. Modal dependent.

Access the solenoid: Lift the rubber tray mat off and remove the two tray screws. You will see the solenoid. It's a white cylinder with a metal bar protruding rearward toward the shifter. You might opt to remove the center console too.

Starter problem:

I was having intermittent starter trouble. I would try to start the Jeep by turning the ignition key. The dash lights, radio, and other electrical would come online, but the starter would not activate.

The Fix: I removed the electrical cables from the starter, unbolted the starter, and then reinstalled the bolts holding the starter in place.

Why this worked: The electrical connections including the ground to the block had become oxidized. By disconnecting and reconnecting the wires and removing and reinstalling bolts, I scraped the oxidation off, making for a good electrical connection.


All times are GMT -5. The time now is 06:50 AM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community