Jeep Garage  - Jeep Forum

Jeep Garage - Jeep Forum (http://www.jeepgarage.org/forums.php)
-   Grand Cherokee - WK (http://www.jeepgarage.org/f5/)
-   -   Water pump 2005 wk 4.7 (http://www.jeepgarage.org/f5/water-pump-2005-wk-4-7-a-52752.html)

Fjaime573 01-11-2013 11:40 AM

Water pump 2005 wk 4.7
 
What is the process to change my water pump my jeep has a hydraulic fan so I'm guessing i will be harder .

2005 Jeep Grand Cherokee Laredo 4x4 4.7 V8

fcdd25 01-13-2013 11:26 AM

Re: Water pump 2005 wk 4.7
 
By "hydraulic fan" do you mean a fan attached to the fan clutch and then threaded onto the water pump pulley?

Combat 01-17-2013 05:44 PM

Re: Water pump 2005 wk 4.7
 
2005 Jeep Truck Grand Cherokee 2WD V8-4.7L VIN N

Vehicle Level http://alldatapro.com/images/a_003366.gif Engine, Cooling and Exhaust http://alldatapro.com/images/a_003366.gif Cooling System http://alldatapro.com/images/a_003366.gif Water Pump http://alldatapro.com/images/arrow1.gif Service and Repair http://alldatapro.com/images/arrow2.gifhttp://alldatapro.com/images/blnk_spc.gifService and RepairPUMP-WATER

REMOVAL
4.7L

http://alldatapro.com/alldata/PRO~V3...8902/115066022

The water pump on 4.7L engines is bolted directly to the engine timing chain case/cover.

A gasket is used as a seal between the water pump and timing chain case/cover.

The water pump can be removed without discharging the air conditioning system (if equipped).

  1. Disconnect negative battery cable from battery.
  2. Drain cooling system. Do not waste reusable coolant. If solution is clean, drain coolant into a clean container for reuse.
WARNING: CONSTANT TENSION HOSE CLAMPS ARE USED ON MOST COOLING SYSTEM HOSES. WHEN REMOVING OR INSTALLING, USE ONLY TOOLS DESIGNED FOR SERVICING THIS TYPE OF CLAMP, SUCH AS TOOL 6094. ALWAYS WEAR SAFETY GLASSES WHEN SERVICING CONSTANT TENSION CLAMPS.

CAUTION: A number or letter is stamped into the tongue of constant tension clamps. If replacement is necessary, use only an original equipment clamp with matching number or letter.

  1. Remove accessory drive belt.
  2. Remove lower radiator hose clamp and remove lower hose at water pump.
  3. Remove seven water pump mounting bolts and one stud bolt.
CAUTION: Do not pry water pump at timing chain case/cover. The machined surfaces may be damaged resulting in leaks.

  1. Remove water pump and gasket. Discard gasket.
CLEANING
Clean the gasket mating surface. Use caution not to damage the gasket sealing surface.

INSPECTION
Inspect the water pump assembly for cracks in the housing, Water leaks from shaft seal, Loose or rough turning bearing or Impeller rubbing either the pump body or timing chain case/cover.

INSTALLATION

http://alldatapro.com/alldata/PRO~V3...8902/115160785

  1. Clean gasket mating surfaces.
  2. Using a new gasket, position water pump and install mounting bolts as shown.. Tighten water pump mounting bolts to 58 Nm (43 ft. lbs. ) torque.
  3. Spin water pump to be sure that pump impeller does not rub against timing chain case/cover.
  4. Connect radiator lower hose to water pump.
  5. Install accessory drive belt.
CAUTION: When installing the serpentine accessory drive belt, belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction.

  1. Refill cooling system.
  2. Connect negative battery cable.
  3. Start and warm the engine. Check for leaks.



http://alldatapro.com/images/blnk_spc.gif


All times are GMT -5. The time now is 06:29 AM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community