Jeep Garage  - Jeep Forum

Jeep Garage - Jeep Forum (http://www.jeepgarage.org/forums.php)
-   Engine Performance/Superchargers/Turbos (http://www.jeepgarage.org/f141/)
-   -   5" Double Wall, slant cut, beveled edge tips (http://www.jeepgarage.org/f141/5-double-wall-slant-cut-beveled-edge-tips-9030.html)

QuickOne 04-30-2010 07:06 PM

5" Double Wall, slant cut, beveled edge tips
 
They are finally getting done! Just like the title says.

They are $110 each before shipping and they will have SRT laser etched on the top.
If you choose no laser etching it's $100 per tip.
I'll have the first prototype in hand on Friday, 05/06.
He have about 40 folks interested, but I wanted to put the info up here as well.
http://i675.photobucket.com/albums/v...chtipProto.jpg

Here is the photo. I know its no Hi-Def photo or anything, but you get the point.

Pm me if your interested, so we can keep you in the loop for any interested buyers.

QuickOne

robpp 04-30-2010 07:11 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
not sure this is the right place:

how about in the srt8 area or the members group buy. either one is good, if you let me know ill move it for you.

Scottina06 04-30-2010 07:19 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
Im in...no laser etch.....PMing


these do install without changing the rear SRt piping right?

QuickOne 04-30-2010 07:40 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
Rob,
I figured I would put it up in Intake and exhaust since I wasn't actually doing the whole group buy, but posting the info. But please feel free to move as you feel fit.
Scott,
These will fit stock pipes. The inlet is actually 3", so it will fit most everyone's systems. Stock on the SRT8 is 2.75", so it's an easy weld for any respectable exhaust guy.
The overall length is 9", but there's at least an inch to cut off on the small side, leaving plenty of meat to weld to.
These will most resemble the stock tips, but just a 5" outlet to fill the hole better.

After thinking more about the Etching, I don't think it would look that good with dual SRT etchings on the tips. "6.1" on one and "HEMI" on the other might be a good one.

I'll put you on the interested list. Once we get the prototype, I'll make any fine tune adjustments, and then we'll get a set installed so we can actually see what it looks like on the Jeep prior to anyone having to jump on board.
Keep ya posted!!!
Quick One!

QuickOne 04-30-2010 07:43 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
Hamze...
Can you explain how you made that happen?
I don't see any 3" in and 5" outlet. And I only see 12" long.

Oh...I see your rocking a 3.7. N/M

QuickOne 04-30-2010 08:05 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
No worries Man.
The SRT has resonaters right behind our tips. You would have to remove the resonators to put those 12" long tips, which would require a lot more work than what these will.
So that half price is quickly lost in the other piping you'd have to buy and weld on.

Or you could just put all 12" on and have them stick out 6" :eek: from your bumper!

QuickOne 04-30-2010 08:13 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
But then your into a 5" section of the pipe? So your going to mod that down from a 5" to a 2.75? Come on bud. If you're doing that much fab to a double wall tip and you can make it look good, then more props to you. For everyone else...This is perfect.

downstate 04-30-2010 08:47 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
Looks great! Had I not gone the Borla route I would have picked these up. I know a couple people here local that might be interested in these - will pass along the information.

Hamze 05-01-2010 07:42 AM

Re: 5" Double Wall, slant cut, beveled edge tips
 
Ooops! guess yesterday night was a little drunk, and being an a$$! hahaha :) .. will delete all my postings in this thread after a while...

Hey Quickone! my apologies bro! Good luck with the tips !! I didnt even notice you're selling those.

Black Ops Auto Works 05-01-2010 07:44 AM

Re: 5" Double Wall, slant cut, beveled edge tips
 
Lmao ^^^^

QuickOne 05-01-2010 05:10 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
Hamze....No biggie...Like I said...No worries Bro!
I'm just doing a group buy. I just really like the 5" tip over the stock 4". Since no one makes a slant cut, which follows the rear bumper lines, I really wanted it. So, I'm glad it's finally getting done, and apparently, so are about 30 other people, which makes it that much better! :)

hawkman996 05-01-2010 08:05 PM

Re: 5" Double Wall, slant cut, beveled edge tips
 
As I said on the red site, I am glad these tips are finally being made. I'm surprised more people have not jumped on board but I'm guessing once a set of tips are installed on a jeep and people see what the end product will look like then a lot more will jump on board.


All times are GMT -5. The time now is 02:11 AM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community