Go Back   Jeep Garage - Jeep Forum > Search Forums

Join Jeep Garage Today
Showing results 1 to 15 of 15
Search took 0.02 seconds.
Search: Posts Made By: Ypahihi
Forum: Troubleshooting/Problems 09-09-2012, 02:00 PM
Replies: 37
Views: 2,653
Posted By 01grand
Re: Quadadrive issues

The transfer case is bolted to the output of the transmission. There are 2 hex plugs on the back of the transfer case, the upper one (fill plug) should have some fluid start to run out when you pull...
Forum: Troubleshooting/Problems 05-09-2012, 04:18 PM
Replies: 1
Views: 10,926
Posted By Milo
Key Stuck In Ignition Fixed!

Per my post, dated 01-05-2012, 09:36 PM.

I found and fixed the key and start problems.

Back in January I was experiencing a problem where I wasn't able to turn the...
Forum: Grand Cherokee - WJ 05-07-2012, 06:26 AM
Replies: 6
Views: 709
Posted By Frango100
Re: Time for a Service

In an other thread a few members where complaining about the WIX fuel filter/regulator. It works ok, but seems to be producing strange noises.
Did you already change the T-case fluid?
And what...
Forum: Troubleshooting/Problems 05-03-2012, 09:07 PM
Replies: 21
Views: 33,078
Posted By mon_21
32 Problems and Suggested fix

Ran across a list of problems and suggested fix for the WJ while surfing the net, they might be of some use to all or some of us....

Jeep*Grand Cherokee*1999-2004*(WJ)

32 Fixes Found

Forum: Grand Cherokee - WJ 03-13-2012, 11:27 PM
Replies: 5
Views: 12,186
Posted By Amelie
Nominate The WJ Owner's Guide To Recommended Mods

(This represents a semi-comprehensive list of the most recommended additions/mods recommended to any new WJ owner from fellow WJ owners)


Projector Headlights (3rd Gen)
HID Kit...
Forum: Tech Tips DIY/How To 02-19-2012, 08:58 PM
Replies: 4
Views: 2,152
Posted By 08Hemi
How to: Wire 3157 CK LED's in 08 WK with 6 ohm Resistor

There is a lot of info on JG for wiring these, but I couldn't find it in one thread so here it goes. Bought these red 3157 ck LEDs from rob (thanks bro) and the 6 phm resistors. I have always wanted...
Forum: Interior/Exterior/Visual 01-27-2012, 04:45 PM
Replies: 10
Views: 1,224
Posted By Amelie
Re: CCFL Rings

I'm not sure if this would work for for you but I use this. I only have 1 CCFL ring on each side not 2 and it's inside the shroud so not all of it is seen.
Forum: Interior/Exterior/Visual 01-26-2012, 11:38 AM
Replies: 10
Views: 1,224
Posted By TJXJWJ
Re: CCFL Rings

I would run your LED's seperate of the box wiring. In other words, run your LED wiring directly to the parking light circuit, then run seperate lines to power the inverter/starter box for the CCFL...
Forum: Interior/Exterior/Visual 12-21-2011, 01:17 PM
Replies: 21
Views: 1,527
Posted By TJXJWJ
Re: What do you think of these?

Forum: Troubleshooting/Problems 12-19-2011, 10:20 PM
Replies: 15
Views: 2,479
Posted By Frango100
Re: Another O2 Sensor Question

It is in fact quite simple. But be aware that the fuel system is always under pressure, even with the engine off. You have to remove the fuel pump relay in the PDC and start the engine. It will...
Forum: Interior/Exterior/Visual 12-17-2011, 09:54 AM
Replies: 17
Views: 1,862
Posted By Amelie
Re: bulbs?

As reynolds mentioned, HIR's would be a good choice for the high beams since we already talked about the warm-up times and power cycling of HID being bad for it. Though the jump in lumens from a 9006...
Forum: Interior/Exterior/Visual 12-15-2011, 11:50 AM
Replies: 17
Views: 1,862
Posted By TJXJWJ
Re: bulbs?

I'd caution against HID hi-beams unless you run your high beams for extended periods. HID and many on-off cycles do not mix well.

If you're popping regular bulbs in your GEN3's, don't spend too...
Forum: Troubleshooting/Problems 12-15-2011, 04:34 AM
Replies: 6
Views: 3,805
Posted By bkr_brad
Just replaced both my front axles a few days ago....

Just replaced both my front axles a few days ago. What a pain, you may want to try soaking the bolts in some penetrating oil before or get a hammer and/or cheater bar. The nut for the axles is a...
Forum: Troubleshooting/Problems 12-07-2011, 08:14 PM
Replies: 15
Views: 3,257
Posted By Frango100
Re: Transmission fluid

The front (kickdown) band adjusting screw is
located on the left side of the transmission case
above the manual valve and throttle valve levers.
(1) Raise vehicle....
Forum: Engine Performance/Intake/Exhaust 03-15-2011, 08:21 PM
Replies: 39
Views: 11,318
Posted By jeepgcoman
Oxygen Sensors and Their Role in Engine Management--A Primer

I am doing this thread due to my recent experience with the Oxygen Sensors (O2) on my Hemi WK. I’ll explain how and why I became very interested in this, and the results of my research and actions....
Showing results 1 to 15 of 15

Forum Jump

All times are GMT -5. The time now is 04:38 AM.

Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2015, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community

JeepGarage.org is in no way associated with or endorsed by FCA US LLC. Chrysler, Dodge, Jeep, Ram, Mopar and SRT are registered trademarks of FCA US LLC.