Go Back   Jeep Garage - Jeep Forum > Search Forums

Join Jeep Garage Today
Showing results 1 to 40 of 49
Search took 0.02 seconds.
Search: Posts Made By: magnumman426
Forum: Troubleshooting/Problems Discussion 05-17-2011, 08:36 PM
Replies: 5
Views: 616
Posted By magnumman426
Forum: Troubleshooting/Problems Discussion 05-17-2011, 08:33 PM
Replies: 1
Views: 417
Posted By magnumman426
Re: codes on my 06 wangler

Check for a leaking cat convertor. Also, check the wiring harness as it passes at the back of the valve cover. There is a large bolt at the rear LEFT side, that has a tendancey to rub through the...
Forum: Troubleshooting/Problems Discussion 05-17-2011, 08:20 PM
Replies: 9
Views: 6,285
Posted By magnumman426
Re: Jeep completely died while driving today. PLEASE HELP

Recommendations: Change both the cam and the crank sensor. The both run on the same 5v reference and same signal lines to and from the pcm.
Forum: Troubleshooting/Problems 05-17-2011, 08:14 PM
Replies: 59
Views: 37,228
Posted By magnumman426
Re: 06 Grand Cherokee - Electrical Problem wih Dash Cluster

The Harness that comes into the cabin is connected to the engine compartment harness. On the left side front fram rail is the c200 connector. We have had many issues of pin pull out here. Doesnt...
Forum: Troubleshooting/Problems Discussion 05-17-2011, 08:05 PM
Replies: 14
Views: 1,606
Posted By magnumman426
Re: Jeep is "bucking" when stopped HELP

Sounds lie a torque convertor problem. Also, and this is just a possibility, there may be a crack in the sump pick-up/filter for the trans, allowing air to be ingested by the converter. Those would...
Forum: Troubleshooting/Problems Discussion 05-17-2011, 07:58 PM
Replies: 8
Views: 677
Posted By magnumman426
Re: 08 WK Will not start.. Sadpanda

It's not always the starter itself, but the solenoid wiring. The connector has a weather seal with shrink tubing. As the tubing gets hot the gkue softens and flows into the connector. Check this...
Forum: Troubleshooting/Problems Discussion 05-17-2011, 07:34 PM
Replies: 4
Views: 750
Posted By magnumman426
Re: stalled out while idling

2005 WK is Drive by Wire. IAC is integrated to the throttle body. It may or may not throw a code. Also, there may be an issue with the EGR system.
Ill check star cases and tsb's and fill in if I...
Forum: Troubleshooting/Problems Discussion 05-17-2011, 07:32 PM
Replies: 12
Views: 5,673
Posted By magnumman426
Re: Need help with uconnect phone plz

There have been issues with the module, it can be reset, but you need a starscan.
I usually go into my phone's wireless connections setup, and just disconnect and reconnect the pairing.
Forum: Troubleshooting/Problems Discussion 05-17-2011, 07:29 PM
Replies: 13
Views: 2,049
Posted By magnumman426
Re: popping noise in front suspension-bwoody/srt bilsteins

Try and make sure that the springs are seated in the cushions properly, and oriented correctly. A misaligned spring will cause that as well.
Forum: Troubleshooting/Problems Discussion 04-12-2011, 05:41 PM
Replies: 9
Views: 2,392
Posted By magnumman426
Re: Jeep makes popping noise?

The blend door is in the center section of the HVAC box. Generally speaking, the actuator is the root cause of the problem, causing the door to come up against the stop, with the motor forcing still,...
Forum: Engine Performance/Intake/Exhaust 04-12-2011, 05:32 PM
Replies: 39
Views: 8,608
Posted By magnumman426
Re: Oxygen Sensors and Their Role in Engine Management--A Primer

Hi guys, just a quick chime-in, most of the slow response codes dont just come from a lack of heat issue, but more overly so, due to a leak in the weld joint of the cats. Slow responsees ar caused by...
Forum: Members Rides 04-04-2011, 11:40 PM
Replies: 38
Views: 3,620
Posted By magnumman426
Re: Four SRT8 VEHICLES

Fuc*** what?!? Lol... by the time you were using the lift, it was almost 60 degrees out, and I was up to my elbows in the wheelwells of that HIT WkSRT8, LOL! CAN'T ROLL A JEEP WITH NO UCA'S AND...
Forum: Members Rides 04-04-2011, 09:06 PM
Replies: 38
Views: 3,620
Posted By magnumman426
Re: Four SRT8 VEHICLES

Hey Guys, just got in and I gotta say..... WOW! Really had a great time with Mario, Atilla and Joe. NX-1 is the place to go for detailing, no doubt. Mario did a great job of fixing a beat-to-hell...
Forum: Troubleshooting/Problems Discussion 04-04-2011, 08:48 PM
Replies: 4
Views: 753
Posted By magnumman426
Re: PCV replacement = stalling?

06 t-body is ETC, and therefore NO IAC.
Do you have any DTC's stored in the pcm? I am an active CERTIFIED Jeep/Chrysler/Dodge technician. I can try to assist you if there are ANY oter secondary...
Forum: Liberty-KJ and KK 04-04-2011, 08:42 PM
Replies: 2
Views: 814
Posted By magnumman426
Re: liberty making noise

Check the stub shaft on the inboard side of the passenger axle, the early Liberty's were prone to rust bildup inside, and the outter splines would shear on the output shaft from the diff to the axle....
Forum: Troubleshooting/Problems 04-04-2011, 08:39 PM
Replies: 8
Views: 3,339
Posted By magnumman426
Re: 4.7 oil filler cap sludge problems

It is normal. happens on all of them up through 2006, actually. When Chrysler/Jeep stopped putting the filler plug in the fill port, that partially alleviated the problem.
Forum: Troubleshooting/Problems Discussion 10-21-2010, 10:35 PM
Replies: 13
Views: 2,260
Posted By magnumman426
Re: Door hinge noise

If the noise keeps up after being greased, replace the hinges. We've seen this problem in the shop a bit already.

MM
Forum: Troubleshooting/Problems Discussion 10-15-2010, 09:52 PM
Replies: 10
Views: 1,191
Posted By magnumman426
Forum: Troubleshooting/Problems Discussion 10-15-2010, 09:51 PM
Replies: 10
Views: 1,191
Posted By magnumman426
Re: P0443 Problem, need some help

https://w05.dealerconnect.chrysler.com/service/mds2002/serviceInfo/en_US/334219.jpg
Forum: Troubleshooting/Problems Discussion 10-15-2010, 09:48 PM
Replies: 10
Views: 1,191
Posted By magnumman426
Re: P0443 Problem, need some help

C3 connector is the one you want to use.
Forum: Troubleshooting/Problems Discussion 10-15-2010, 09:46 PM
Replies: 10
Views: 1,191
Posted By magnumman426
Re: P0443 Problem, need some help

C4 Connector: TRANSMISSION

https://w05.dealerconnect.chrysler.com/service/mds2002/serviceInfo/en_US/818921f7.gif MODULE-POWERTRAIN CONTROL C4 - BLACK/GREEN 38 WAY

CAVCIRCUITFUNCTION1T60...
Forum: Troubleshooting/Problems Discussion 10-15-2010, 09:45 PM
Replies: 10
Views: 1,191
Posted By magnumman426
Re: P0443 Problem, need some help

C3 connector:

https://w05.dealerconnect.chrysler.com/service/mds2002/serviceInfo/en_US/818921f5.gif MODULE-POWERTRAIN CONTROL C3 - BLACK/NATURAL 38 WAY

CAVCIRCUITFUNCTION1--2--3K342 20BR/WTASD...
Forum: Troubleshooting/Problems Discussion 10-15-2010, 09:44 PM
Replies: 10
Views: 1,191
Posted By magnumman426
Re: P0443 Problem, need some help

C2 Connector

https://w05.dealerconnect.chrysler.com/service/mds2002/serviceInfo/en_US/818921f3.gif MODULE-POWERTRAIN CONTROL C2 - BLACK/ORANGE 38 WAY

CAVCIRCUITFUNCTION1K10 16DB/OR (GAS EXCEPT...
Forum: Troubleshooting/Problems Discussion 10-15-2010, 09:43 PM
Replies: 10
Views: 1,191
Posted By magnumman426
Re: P0443 Problem, need some help

PCM C1 Connector:

https://w05.dealerconnect.chrysler.com/service/mds2002/serviceInfo/en_US/818921f1.gif MODULE-POWERTRAIN CONTROL C1 - BLACK/BLACK 38 WAY

CAVCIRCUITFUNCTION1K98 16DB/YL...
Forum: Troubleshooting/Problems Discussion 10-13-2010, 08:05 PM
Replies: 10
Views: 1,102
Posted By magnumman426
Re: my 4.7L WK idles at 500 RPM

Threason is that the EGR is a LINEAR system, completely housed electronic unit and it is not recommended to use any typf of cleaning solvents within them. There are known issues with the EGR valves...
Forum: Troubleshooting/Problems Discussion 10-13-2010, 08:02 PM
Replies: 2
Views: 871
Posted By magnumman426
Re: === Tire pressure sensor from WK '08 on WK '05

The 08 sensors will not work with 05 because of the transmitter frequency. The receivers ar not made to pick up that frequency, and can not be reprogrammed.
Forum: Troubleshooting/Problems 10-13-2010, 08:00 PM
Replies: 13
Views: 2,586
Posted By magnumman426
Re: Hello everyone, 2006 laredo wont start???

Check the wire to the starter solenoid. In many instances of vehicles with the same problem in our shop, the terminal end on the starter was corroded, and the connector from the wiring harness was as...
Forum: Troubleshooting/Problems Discussion 10-13-2010, 07:51 PM
Replies: 12
Views: 3,853
Posted By magnumman426
Re: How to recalibrate the seat sensor ?

Special seat weight (people simulators) and a starscan needed. Dealer only.
Forum: Troubleshooting/Problems 10-10-2010, 08:52 AM
Replies: 6
Views: 1,735
Posted By magnumman426
Re: 2006 g/c hesitation

Tsb# 21-08-005
Forum: Troubleshooting/Problems 10-10-2010, 08:48 AM
Replies: 24
Views: 4,816
Posted By magnumman426
Re: High idle problems

About 3-400, but I'd rather see it done right, than not. That was the same place the TJ I worked on got theirs from.
Forum: Troubleshooting/Problems 10-10-2010, 08:39 AM
Replies: 2
Views: 792
Posted By magnumman426
Re: WJ 4.7 Gearbox Fault

P0700 is only a PCM code for trans controller fault. You need more specific info from the trans controller side of the PCM. This sounds like the common issue with the valve body in the 45RFE...
Forum: Troubleshooting/Problems Discussion 10-10-2010, 08:32 AM
Replies: 4
Views: 1,789
Posted By magnumman426
Re: 4.7L V8 Manifold Leak - First Generation

This is a common issue with the 4.7L exhaust manifold bolts. It is usually the rear most bolts, upper or lower or both, and is usually a pretty quick fix. New Bolts and Gasket and you're good to go.
Forum: Troubleshooting/Problems 10-09-2010, 09:15 PM
Replies: 4
Views: 774
Posted By magnumman426
Re: Grumble while Turning...

Differentials and transfer case in the '05 are different than the '00.

Lubed the lower steering bushings? No rack in an '00 model, so are you referring to the drag link, the tie-rod ends and the...
Forum: Troubleshooting/Problems 10-09-2010, 09:11 PM
Replies: 24
Views: 4,816
Posted By magnumman426
Re: High idle problems

I would recommend getting a DEALER replacement, not from the outside market. I had a 1999 wrangler come in with 3 computers replaced from the same company. They complained on and on, but bought one...
Forum: Troubleshooting/Problems Discussion 10-09-2010, 09:08 PM
Replies: 10
Views: 1,532
Posted By magnumman426
Re: Autostick inoperative

Complete Shifter assembly!! Get it replaced ASAP!
Forum: Troubleshooting/Problems 10-09-2010, 10:40 AM
Replies: 4
Views: 774
Posted By magnumman426
Re: Grumble while Turning...

Grind and thump are 2 different things. Need a little more specific info to help you PINPOINT the noise
Forum: Troubleshooting/Problems 10-09-2010, 10:37 AM
Replies: 9
Views: 5,079
Posted By magnumman426
Re: Grinding Noise

Take a look at the parking shoes BEHIND the rotors. They have a tendancy to separate from the shoeplate with age.
Forum: Troubleshooting/Problems Discussion 10-09-2010, 10:34 AM
Replies: 3
Views: 4,555
Posted By magnumman426
Re: P0730

Case NumberK92303407 Vehicle IssueTransmission will not upshift from third into fourth gear.;The transmission Neutrals out when trying to up shift to fourth or shifts back to third after attempting...
Forum: Troubleshooting/Problems Discussion 10-09-2010, 10:31 AM
Replies: 7
Views: 1,276
Posted By magnumman426
Re: RKE Module Quit

08 GC Should still be under warranty (3/36), unless your mileage is out the door! I'd check to see if the H30 Recall was done as well.
Forum: Troubleshooting/Problems Discussion 10-09-2010, 10:25 AM
Replies: 3
Views: 781
Posted By magnumman426
Re: passenger window problem

THis sounds like the common issue with the door modules. What we do in the shop is, replace both window regulators, and both door modules. Also, I would check to see if the bottom front end of the...
Showing results 1 to 40 of 49

 
Forum Jump

All times are GMT -5. The time now is 01:51 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community