Go Back   Jeep Garage - Jeep Forum > Search Forums

Join Jeep Garage Today
Showing results 1 to 15 of 15
Search took 0.01 seconds.
Search: Posts Made By: ebrodnick
Forum: Troubleshooting/Problems 07-27-2013, 08:54 PM
Replies: 15
Views: 600
Posted By ebrodnick
All problems fixed and running great. Thank you...

All problems fixed and running great. Thank you all.
Forum: Troubleshooting/Problems 07-26-2013, 11:43 PM
Replies: 15
Views: 600
Posted By ebrodnick
Re: New cylinder heads

Put on a Coolant system pressure tester. Saw a dripping leak from one of the heater hoses. Explains the white smoke from that side of the engine. Next was to take a look at the oil sending unit....
Forum: Troubleshooting/Problems 07-23-2013, 12:11 AM
Replies: 15
Views: 600
Posted By ebrodnick
I appreciate your response. Hopefully it works...

I appreciate your response. Hopefully it works out. Ordered a mopar sending unit online since I read terrible things about aftermarket. Seems like an odd coincidence for that to go out at the same...
Forum: Troubleshooting/Problems 07-21-2013, 11:45 PM
Replies: 15
Views: 600
Posted By ebrodnick
Well not only am I trying to figure out the oil...

Well not only am I trying to figure out the oil pressure but the white smoke from passenger side engine bay and exhaust pipe.
Forum: Troubleshooting/Problems 07-19-2013, 06:55 PM
Replies: 15
Views: 600
Posted By ebrodnick
Well before I tear it all down again any last...

Well before I tear it all down again any last thoughts on my situation? I suppose this time ill take more care making sure the engine block mating surface is clean and smooth before putting on...
Forum: Troubleshooting/Problems 07-18-2013, 09:00 PM
Replies: 15
Views: 600
Posted By ebrodnick
For my 02 wj with the 4.7 the torque sequence...

For my 02 wj with the 4.7 the torque sequence was...

1-10 15 ft lbs
Then 1-10 35 ft lbs
Then 11-14 18 ft lbs
Then 1-10 90 degrees
Then 11-14 19 ft lbs

I dipped the large bolts in oil...
Forum: Troubleshooting/Problems 07-18-2013, 08:18 PM
Replies: 15
Views: 600
Posted By ebrodnick
Is there any correlation to bad head gasket...

Is there any correlation to bad head gasket install and oil pressure falling to 0?
Forum: Troubleshooting/Problems 07-18-2013, 05:45 PM
Replies: 15
Views: 600
Posted By ebrodnick
I was meticulous on the torque sequence as well....

I was meticulous on the torque sequence as well. the white smoke is coming from the passenger side of the engine and exhaust. It is fairly continuous but reduces a little once the engine warms up....
Forum: Troubleshooting/Problems 07-18-2013, 01:33 PM
Replies: 15
Views: 600
Posted By ebrodnick
The chances of a bad head at run likely being...

The chances of a bad head at run likely being that they were new, but you never know I guess. I bought new head gaskets for this install. The only thing I reused were the bolts.
Forum: Troubleshooting/Problems 07-18-2013, 11:18 AM
Replies: 15
Views: 600
Posted By ebrodnick
There is also white smoke coming from passenger...

There is also white smoke coming from passenger side engine and exhaust. Lessens when engine warms up. White makes me think coolant. I didnt use new head bolts because I took a straight edge to all...
Forum: Troubleshooting/Problems 07-18-2013, 10:46 AM
Replies: 15
Views: 600
Posted By ebrodnick
New cylinder heads

After dropping a valve seat I bought 2 brand new cylinder heads from power torque. The install went smooth. Replaced timing set and all gaskets. Engine starts up a seems to run great. Took for a...
Forum: Troubleshooting/Problems 07-18-2013, 10:14 AM
Replies: 13
Views: 550
Posted By ebrodnick
Problem solved. Unbolted starter and the plug was...

Problem solved. Unbolted starter and the plug was loose. DOH! thanks for your replies.
Forum: Troubleshooting/Problems 07-17-2013, 04:37 PM
Replies: 13
Views: 550
Posted By ebrodnick
Is there any particular sensor(s) that will...

Is there any particular sensor(s) that will prevent the engine from cranking if unplugged?
Forum: Troubleshooting/Problems 07-16-2013, 11:28 PM
Replies: 13
Views: 550
Posted By ebrodnick
Alright I will give fuse 8 a check to see if it's...

Alright I will give fuse 8 a check to see if it's blown. As far as ground wires go I'm almost positive everything went back to its initial spot. How many ground wires are there on the wj and do you...
Forum: Troubleshooting/Problems 07-16-2013, 01:06 PM
Replies: 13
Views: 550
Posted By ebrodnick
2002 limited alarm lockout?

Hey all,

After spending the weekend replacing both cylinder heads due to a dropped valve seat.

Anyway, everything went smooth for the most part. After hooking up the battery and hitting the...
Showing results 1 to 15 of 15

 
Forum Jump

All times are GMT -5. The time now is 02:57 PM.


Powered by vBulletin® Version 3.8.8 Beta 4
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
Copyright 2012 - JeepGarage.Org
The Jeep Grand Cherokee Owners Community